Pages

Wednesday, March 24, 2010

Harmonized Standards List Updated 3/2010 – EMCD & LVD

New lists of harmonized standards for the EMC Directive and the Low Voltage Directive have been published in the Official Journal of the European Union.
Of note, this revision now includes inline explanatory comments. Brief explanations have been added to certain line items, line items that could prove to be confusing without them, an example of one is for EN 55022, which reads;
" Each of the four following standards provide presumption of conformity until 1.10.2011: EN 55022:1998, EN 55022:1998 + A1:2000, EN 55022:1998 + A2:2003, EN 55022:1998 + A1:2000 + A2:2003"
It's refreshing to see that these clarifications are being added. This will hopefully make interpreting which harmonized standards are applicable much easier, for the average compliance engineer. Although, nothing is ever perfect and one should contact an expert if in doubt.
By the way, for those of you reading this on the West side of the "Pond", the date in the above quote is October 1st, 2011 and not January 10th, 2011.
Copies of the new lists can be found  in the European Conformity Assessment section of the Compatible Electronics, Inc. conformity assessment web page.

Wednesday, March 10, 2010

List of ETSI 301 489 EMC standards applicable under article III 1.(b) of 1999/5/EC ( R&TTE Directive ).

This is a flat list of the ETSI 301 489 series test standards. For more information on any of these, visit http://pda.etsi.org/pda/queryform.asp for a direct search on the ETSI site. This list and other R&TTE related material is available on the Compatible Electronics European Conformity Assessment page.

ETSI EN 301 489-1 Common Technical requirements
ETSI EN 301 489-2 Specific conditions for radio paging equipment
ETSI EN 301 489-3 Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 40 GHz
ETSI EN 301 489-4 Specific conditions for fixed radio links, Broadband Data Transmission System Base stations, ancillary equipment and services
ETSI EN 301 489-5 Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment (speech and non-speech)
ETSI EN 301 489-6 Specific conditions for Digital Enhanced Cordless Telecommunications (DECT) equipment
ETSI EN 301 489-7 Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS)
ETSI EN 301 489-8 Specific conditions for GSM base stations
ETSI EN 301 489-9 Specific conditions for wireless microphones, similar Radio Frequency (RF) audio link equipment, cordless audio and in-ear monitoring devices
ETSI EN 301 489-10 Specific conditions for First (CT1 and CT1+) and Second Generation Cordless Telephone (CT2) equipment
ETSI EN 301 489-11 Specific conditions for terrestrial sound broadcasting service transmitters
ETSI EN 301 489-12 Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth Stations operated in the frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service (FSS)
ETSI EN 301 489-13 Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech and non-speech)
ETSI EN 301 489-14 Specific conditions for analogue and digital terrestrial TV broadcasting service transmitters
ETSI EN 301 489-15 Specific conditions for commercially available amateur radio equipment
ETSI EN 301 489-16 Specific conditions for analogue cellular radio communications equipment, mobile and portable
ETSI EN 301 489-17 Specific conditions for Broadband Data Transmission Systems
ETSI EN 301 489-18 Specific conditions for Terrestrial Trunked Radio (TETRA) equipment
ETSI EN 301 489-19 Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating in the 1,5 GHz band providing data communications
ETSI EN 301 489-20 Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite Services (MSS)
ETSI EN 301 489-22 Specific conditions for ground based VHF aeronautical mobile and fixed radio equipment
ETSI EN 301 489-23 Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) Base Station (BS) radio, repeater and ancillary equipment
ETSI EN 301 489-24 Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for Mobile and portable (UE) radio and ancillary equipment
ETSI EN 301 489-25 Specific conditions for CDMA 1x spread spectrum Mobile Stations and ancillary equipment
ETSI EN 301 489-26 Specific conditions for CDMA 1x spread spectrum Base Stations, repeaters and ancillary equipment
ETSI EN 301 489-27 Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)
ETSI EN 301 489-28 Specific conditions for wireless digital video links
ETSI EN 301 489-29 Specific conditions for Medical Data Service Devices (MEDS) operating in the 401 MHz to 402 MHz and 405 MHz to 406 MHz bands
ETSI EN 301 489-31 Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low Power Active Medical Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P)
ETSI EN 301 489-32 Specific conditions for Ground and Wall Probing Radar applications
ETSI EN 301 489-33 Specific conditions for Ultra Wide Band (UWB) communications devices

Thursday, March 4, 2010

IECEE Battery Ruling

A battery charger
Image via Wikipedia
An issue was brought to the attention of the IECEE regarding CB Certificates for products containing secondary cells (Lithium Ion Battery cells) that are certified to UL 1642 as well as Secondary Battery Packs certified to UL 2054.
These UL standards are not harmonized with the IEC 62133 – “Secondary Cells And Batteries Containing Alkaline Or Other Non- Acid Electrolytes - Safety Requirements For Portable Sealed Secondary Cells, And For Batteries Made From Them, For Use In Portable Applications.”
After deliberation the IECEE issued a ruling indication that a CB Certificate could not be issued for products containing secondary cells that were not in compliance with IEC 62133. However as most secondary cells are currently certified only to UL standards, a phase in period was established.
At the time of this writing, the phase in time table is as follows;
Currently
  • CB Certificates can stand as issued. Note that CB Certificates need to be renewed every 3 years.
New certificates, Until June 2010
  • CB Certificates can continue to be issued using the UL standards for secondary cell certification.
New certificates, June 2010 thru June 2011
  • CB Certificates can be issued using the UL standards for secondary cell certification, if additional testing is conducted on the secondary cells to show compliance to IEC 62133.
After June 2011
  • Secondary cells must have a CB Certificate showing compliance with IEC 62133 to be accepted in an end product evaluation for CB Certification.
There is a good possibility that this time table will be adjusted to allow battery manufacturers time to get secondary cells tested and CB Certification issued.
UL has indicated that they will start the process to harmonize there requirements with IEC 62133.
What does this mean to you and me?
The real effect on most of us is that we will need to move to have our battery suppliers get third party certification on the secondary cells we are using. Otherwise we cannot self certify to the Harmonized EN Standard (EN60950-1, EN61010-1, EN60335-1, EN60065, EN60204-1, etc.) and it will become increasingly difficult to get our products NRTL Listed.
Article by Ercell Bryant, please visit Compatible Electronics on the web.